`
Dock Hardware Logo
.:: Online Catalog
Cypress River Dock Murrells Inlet South Carolina
BARN ISLAND BOAT LAUNCH STONINGTON, CT
SERVICES
Dock Hardware & Marine Fabrication Products
BACK TO TOP
ALUMINUM WALKAWAYS
ALUMINUM RAMP
Our ramps are available in varying lengths. Single span to fit any property, or to
accommodate extreme water level fluctuations.
~Rustproof, low maintenance 6061-T6
marine grade aluminum construction.
Stainless steel hardware.
~Safer when wet, skid-resistant EZ-grip
decking.
~Easy access for dock carts with 1/4"
aluminum tread plate ramp.
~Better load distribution with piano-style
hinge at wall connection, eliminates
gap between shoreline and gangway.
~50 PSF live load minimum; larger
loading available (contact factory).
~longer spans, greater loads are
possible with truss design.
~Less wear and tear on floating dock
with segmented 2-1/2" x 9" UHMV
rollers for protection.
~Lightweight, docks require less
flotation economical to transport.
NEW
RESIDENTIAL OR COMMERCIAL USE
AFFORDABLE AND ECONOMICAL
10x60 Aluminum Ramp 3x16 Aluminum Ramp with PT Decking
10x60 ALUMINUM RAMP HEAVY DUTY 3x16 ALUMINUM RAMP W/PT DECKING
THESE RAMPS CAN BE PURCHASED
WITH ALUMINUM DECKING,
PRESSURE TREATED
DECKING,COMPOSITE DECK OR
IPE DECKING
SUPPLIED WITH BULKHEAD HINGE
CONNECTION & WHEELS ON
OTHER END.
4x34 Aluminum Ramp Aluminum Ramp
4x34 ALUMINUM RAMP
Aluminum Ramp Construction Aluminum Ramp Details
5x16 Aluminum Ramp 6x24 Aluminum Ramp
5x16 ALUMINUM RAMP
4x24 Aluminum Ramp with ADA Handrails 4x30 Aluminum Ramp
4x24 ALUMINUM RAMP ADA HANDRAILS 4x30 ALUMINUM RAMP
BACK TO TOP
ALUMINUM FLOATING DOCKS
ALUMINUM FLOATING DOCKS
Our aluminum structural frames are extruded from 6061 T 6 aluminum
alloy, and offer a 10" width side rail. These structural channels offer a wide variety of decking's that can be used with them: pressure-treated wood, our aluminum decking, or even our new lightweight concrete pre-cast sections. Our aluminum docks are welded with the hinge mount extrusions that are matched in our shop prior to shipment. Cleats and accessories are welded or bolted to meet your requirements. Flotation may be detachable for easier unloading and shipping. These floating docks are fabricated to withstand a minimum uniform live load of 20 pounds per sq ft. Applied vertically. The flotation is sized to provide a minimum free-board of 10" under dead load conditions. Additional flotation is added to support the gangways load without
creating undue distortion to the dock.
Should your requirements include smaller
lengths, widths and decking types, call one of
our sales representatives for a price
quotation at the current market price of
aluminum.
Aluminum Floating Dock Aluminum Floating Dock
Floating Dock Aluminum Floating Dock
THIS PARTICULAR FLOAT IS (2) 6x20
ALUMINUM FRAME WITH CEDER
DECKING AND SKIRTING.
Aluminum Floating Docks Aluminum Floating Dock
6 x 24 Aluminum ADA Fishing Platform
Aluminum Ramp Aluminum Ramp
4x24 Aluminum Ramp ADA Handrails Fishing Platform
BACK TO TOP
WOOD FLOATING DOCKS
WOOD FLOATING DOCK
Dock Hardware & Marine has designed a wood floating dock to meet your toughest marine environment. Our sub-frames are fabricated from #1 southern yellow pine lumber, and treated to specification .60 CCA. Our own galvanized wood dock hardware is then installed on our sub-frames using 1/2" galvanized carriage bolts. We then select the correct flotation to give you the desired free-board conditions under dead load conditions. The end product is marine structure that will give you 20-30 years of trouble free service. All of our wood marine floats are interchangeable to allow you to create
almost any marine float layout.
Wood Floating Dock
PARALLAM LONG LENGTH FLOATS
Our Parallam series floats with stringers either 1.75" width x 11 7/8" height or 2.69" width x 11 7/8" height can withstand the most extreme marine environment any wood floating structure has been designed for. Manufactured to lengths up to 48 feet long and engineered with a utility raceway accessible from
the top deck boards, these floats can be the answer to your
square foot budget for a quality floating structure. For other applications and sizes manufactured, please call our engineering department for price quotation to your specifications.
Parallam Long Length Float
LOW PROFILE ROWING SHELL FLOATS
Is your rowing crew in need of a low profile and high load carrying rowing shell float for your rowing crew or school? We have the answer. Slimline Series 7" profile floats have been engineered to give your crew the low boarding heights and stable boarding / unloading platforms they have always dreamed of.
Please Call
Low Profile Rowing Shell Floats Low Profile Rowing Sheel Float Frame
BACK TO TOP
STEEL DOCKS
Dock Hardware & Marine Fabrication now offers structural steel frames to accommodate any design requirements of yours. These steel frames are fabricated from 1-1/2" x 1-1/2" x 3/16" steel angles. Frames are welded into
(4ft.), (6 ft.) and (8 ft.) wide sections, in either 10 or 20 ft. Lengths. Once all welding and fabrication has been completed, the frames are hot dipped galvanized. We suggest that you contact one of our experienced
representatives to select the correct flotation per application. For a
wide variety of deck surfaces, see our section
on decking's or walk surfaces.
Steel Frame Floating Dock
Detail of Steel Dock
Steel Walkway Dock Steel Dock
BACK TO TOP
STATIONARY DOCKS
Stationary docks can be easily assembled and installed using our lightweight cast dock brackets. This hardware is designed to be used on most lumber and used with 1 1/2" ID schedule 40 galvanized pipe. Mounting hardware is included.
Stationary Dock
Stationary Dock
Diagram of Stationary Dock
BACK TO TOP
LAUNCHING DOCK SYSTEMS
LAUNCHING DOCK SYSTEMS
Sport Port is an effortless launching and docking system for your personal watercraft. It provides a safe and stable platform for easy parking, refueling and engine flushing. Just drive up on the sport Port and your docked. The non-skid deck surface provides stable footing while the multi-chine design offers minimum resistance when docking and launching. It makes a good fit for all types of personal watercraft, from stand-up machines to three seater's. Sport Port floats with the tide and/or water level changes, so your personal watercraft is always ready when you are. The tough "Poly" shell will not crack or puncture (under normal use of course), yet will not damage your personal watercraft. The foam core technology provides plenty of flotation and renders sport float unsinkable. Call for more information or to place a order!
Jet Ski Launch Kayak Launching System
Jet Ski Launching System Boat Launching Dock Systems
ALUMINUM BOAT HOISTS
Dock Hardware & Marine now offers aluminum boat hoists designed and engineered to insure the same quality and dependability that has been synonymous with our name. These all aluminum boat hoists frames are extruded from high tensile aluminum alloy, insuring maximum support and stability. Stylish canopy covers are available in several eye catching colors. The 18 oz. Nylon reinforced vinyl construction is durable and long lasting. Call one of our technical experts for further information regarding larger models available.
Aluminum Boat Hoists
FLOATING BOAT LIFTS
Our Polylift Floating Boat Hoists use high density polyethylene pipe for its flotation. This material provides extra buoyancy when submerged to minimize the downward load on docks. Our Poly lift tanks are not affected by chemicals, ice, heat, cold or salt. They are ideal for all water conditions. The polylift can adapted to nearly any mooring situation or boat style. With a lifetime warranty on its flotation members and 5 years on its mechanism, it is virtually trouble free. The Polylift heavy duty galvanized frame is fabricated from structural steel. Case hardened bolts and a patented torsion bar clamp along with an exclusive center brace provide the greatest stability of any boat lift on the market. From lift capacities of 2000 lbs to 2400 lbs and personal watercraft models available.
Floating Boat Lifts
PERSONAL DOCKSIDE WATERCRAFT LIFTERS
Dock Hardware & Marine Fabrication now offers a personal watercraft lift that attaches to either your floating or stationary docks in as little as 30 minutes. These aluminum lifts feature a friction braking system that applies a constant holding action to the watercraft being lifted. Similar 2-craft lifts are available on request. Consult factory for pricing. Dockside lifts are Fed ex-able.
Personal Dockside Watercraft Lifter Dock Side watercraft Lifter
BEACH RAILER SYSTEM
New to our product line is our Marine Beach Railer Systems in either aluminum or
galvanized steel. These boat cradles can accommodate vessels weighting from 2000 lbs. to 8000 lbs. in weight. The gentle launch these beach railer systems provide your water craft and float planes can be controlled by our remote control unit from a range as far away as 250 ft. They are a practical alternative to constructing long and expensive permanent piers to gain access to usable water bordering your property. Our curved track sections can be pieced together to grade over seawalls and rough terrain property.
Beach Railer System
BACK TO TOP
PILE HOLDERS
Roller Pile Holders
Our Roller Pipe Holders are designed for easy installation and removal. Designed to be used with round piles, they allow the free movement of the dock with the tides and current fluctuations at your location. Fabricated from 1-1/2" schedule 40 pipe, and secured to sturdy frame, they offer your dock secure attachment to your piles while providing a roller for the pile to move up and down on. The rubber roller is engineered to absorb high impacts and is sleeves with either a 1/2" or 5/8" bushing.
Roller Pile Holder Roller Pile Holders
These roller holders are generally used in areas of turbulent winds and currents.
PH-R12" Roller Pile Holders for use with 10" piles
PH-R14" Roller Pile Holders for use with 12" piles
PH-R16" Roller Pile Holders for use with 14" piles
PH-R18" Roller Pile Holders for use with 16" piles
Conventional Pile Holders
Our Conventional Pile Holders are designed for easy installation and removal. Designed to be used with round piles, they allow the free movement of the dock with the tides and current fluctuations at your location. Fabricated from 1-1/2" schedule 40 pipe, and secured to a sturdy frame, they offer your dock a secure attachment to your piles.
Conventional Pile Holders
These conventional holders are generally used in areas
of calm winds and currents.
PH 10" Pile Holders for use with 8" piles
PH 12" Pile Holders for use with 10" piles
PH 14" Pile Holders for use with 12" piles
PH 16" Pile Holders for use with 14" piles
PH 18" Pile Holders for use with 16" piles
GALVANIZED WELDED PIPE HOLDERS
Our galvanized pipe holders are designed to be used with a variety of diameter pipes. They allow the free up and down movement of your float, while securing the float in its location. Mounting holes are 1/2" in diameter, and we suggest you use stainless steel fasteners to secure them to your floats.
Welded Pipe Holders Galvanized Welded Pipe Holders
2" pipe holders
3" pipe holders
6" pipe holders
Our split pipe holder is designed with ease of installation and removal in mind. This two piece pipe holder is fabricated to be used with 2" O.D. pipe. Complete with 3/8" hex bolts sets. Mounting holes are 1/2" in diameter.
We suggest you use stainless steel mounting bolts.
SQUARE INTERNAL PILE GUIDES WITH ROLLERS
Our Square Pile Holders are designed for internal piling applications and are fabricated from 4"x 4"x1/4" steel angles. Fastening frame uses 1/2" galvanized carriage bolts to attach to your dock slips and the roller assembly is designed for easy replacement of the strong UHMV rollers. Available with either stainless steel Axels', offering very little defection; or galvanized steel Axels'; with either grey rubber rollers or UHMV rollers, these guides are ideal for either round or concrete pilings in areas of strong winds or violent currents.
Internal Pile Guides with Rollers Square Internal Pile Guides with Rollers
They are ideal for either round or concrete pilings. Considered a must in areas of high winds or currents.
SQ-R12" Roller Pile Holders for use with 10" piles
SQ-R14" Roller Pile Holders for use with 12" piles
SQ-R16" Roller Pile Holders for use with 14" piles
WELDED PILE HOLDERS
Our Welded Pile Holders can be used with round pilings from 10" diameter through 18" diameter. They are less expensive than our conventional pile holders, but hold your docks firmly in place. Hoops are bent from 1-1/2" schedule 40 pipe and welded to 5"x 5"x 1/4" steel plates. They are then galvanized and ready for shipment. Each pile holder can be mounted with (8) 1/2" galvanized carriage bolts and our back up plates.
Welded Pile Holders Welded Pile Holders
WPH 10" Holder for 8"pile
WPH 12" Holder for 10" pile
WPH 14" Holder for 12" pile
WPH 16" Holder for 14" pile
WPH 18" Holder for 16" pile
Square Internal Pile Guides with Rollers and Removable Closure BeamsSQUARE INTERNAL PILE GUIDES WITH ROLLERS AND REMOVABLE CLOSURE BEAMS
These internal pile guide holders are designed for those applications where one
side of the holder is removable at the whalers edge to allow you to float your
docks away from their anchor piling.
Fastening the frame into your floats substructure is with either 1/2" or 5/8"
galvanized fasteners. The removable closure beam is secured to the frame with
(2) 3/4" x 6" ss hex bolts through the outside whaler and splicer blocking.

IDEAL FOR APPLICATIONS WHERE INTERNAL PILE GUIDES OFFER LONGER
BERTHING LENGTHS ALONG YOUR FLOATS PERIMETER, YET STILL BEING
ALLOWED TO FLOAT YOUR DOCKS AWAY FROM ITS PILING IN THOSE TAIN
INSTANCES, DREDGING, WINTERIZATION, ETC.
Outside Heavy Duty Pile GuideOUTSIDE HEAVY DUTY PILE GUIDES
Our Heavy Duty Pile Guides have been engineered to safely secure heavy pile
loading conditions generated by concrete floating structures as well as our
heavier Parallam beam series floats with 3"
OD natural urethane rollers supported by 1" OD SS axel's and 1/2" thick steel
support gussets on each leg. Our engineers have developed these guides for
the heaviest loading conditions.

These Heavy Duty Pile Guides can be shopped with either natural urethane
wear blocks or urethane rollers Compared to any other Pile Guides on the U.S.
Market, these top quality guides will offer your float(s) the best protection against
storm and berthing loads. Engineering loading data is available upon request.
Pile Guides with Urethane Rollers Pile Guides
Aluminum Pile Guide
This particularly pile guide is made out of Aluminum.
BACK TO TOP
DOCK CLEATS
DOCK CLEATS
We also offer a wide selection of mooring cleats to meet all your needs. We stock a wide selection of stainless steel fasteners to secure these
cleats to your dock seawall.
Cast Aluminum Dock Cleats CAST ALUMINUM "S" CLEATS
Length-Inch Weight-Ibs Bolt Size
10" 1.50 1/2"
12" 2.50 1/2"
15" 3.40 1/2"
HOT DIPPED GALVANIZED (CAST)
Length-Inch Weight-Ibs Bolt Size
8" 1.50 5/16"
10" 2.12 3/8"
12" 3.56 3/8"
14" 5.88 1/2"
18" 11.00 5/8"
Hot Dipped Galvanized Cleats
CAST ALUMINUM CONCRETE DOCK CLEATS
Length-Inch Weight-Ibs Bolt Size
10" 1.50
Aluminum Dock Cleats CAST ALUMINUM DOCK CLEATS
Length-Inch Weight-Ibs Bolt Size
8" .50 5/16"
10" .75 5/16"
Cast Aluminum Dock Cleats
BACK TO TOP
DOCK FLOATS
Dock Hardware & Marine offers an advanced line of easily installed dock floats with maximum lift capacity. Designed for the waterfront resident, boaters, marina owners. The floats are constructed of thick walled rotationally molded plastic and filled with expanded polystyrene - the finest flotation material available today. The thick walled plastic float case is packed with styrene that is environmentally approved and exceeds all government regulations. Shell is constructed of 100 virgin material. These floats are the finest and most economical on the market today. Perma float drums offer durable flotation that can be easily applied to any new or existing dock system. Perma float drum is rotationally molded which eliminates seams that could result in separation and leakage. The 1/8" thick shell is made of tough virgin polyethylene with UV light inhibitors. The tough shell prevents damage to the flotation from sun, saltwater, debris, oil, gas, and marine organisms. Perma float is foam filled with expanded polystyrene which contains no CHCS or HCF'S. Perm afloat has a flat top with molded in mounting holes for easy attachment to any dock framework whether it be wood, steel, or aluminum. Perma float drums will provide long lasting and carefree flotation which will result in long range savings for the simple public and recreational dock, or the complex commercial marina. Use Perma floats to support, boat docks and courtesy floats, breakwaters and no wake signs, boat houses or swim floats. Marinas, fuel docks, fish farming rafts, pipelines, dredging equipment, etc.
Permafloat
BACK TO TOP
DOCK & POST BUMPERS PILE CAPS
DOCK & POST BUMPERS
All Dock Edge + Inc. Dock and Boat Protection Systems are manufactured with a specially formulated flexible PVC resin. This resin contains a UV inhibitor package which will prevent the profiles from turning yellow in the sun. Also included is a fungicide package to prevent the products from turning (black blotches) over time. The profiles are finished in a bright white finish. This finish will give your dock that completed look. Several of the profiles are "Air Cushion Profiles". This "Air Cushion" is accomplished with the use of connectors, end plugs, and 90 degree corners. When the system is assembled on the dock you in essence have a system similar to boat fender around the perimeter of you dock. This "Air Cushion" will help absorb the impact from those once in a while unavoidable collisions with the dock which we all have. One severe impact with the dock can cause damage not only to the dock but also the boat. This can lead to very costly repairs for both. Dock Edge offers the only complete system available. Several of the profiles can be mounted vertically on moor pilings or entrances to boathouse. With 9 profiles to choose from we have a system for every dock application, from pipe docks, permanent docks, launching ramps, sea walls, floating docks, and moor pilings. Each profile is covered by a two year limited warranty when installed as per our instructions. All profiles include mounting instructions in each carton or pack.
Dock and Post Bumpers
Dock Bumpers
Dock Bumpers
"ULTRA FEND"
CONTINUOUS LENGTH FENDERING SYSTEMS
Ultra poly offers "Ultra Fend," UHMV-PE fendering systems, for pile wraps and boards in continuous lengths. Because of its low coefficient of friction and high impact strength "Ultra Fend" allows vessels to glide freely along its surface while protecting against chipping, shredding, and catching due to impact. Ultra Fend is available in standard black or custom UV-stabilized colors, flat, formed, or fabricated to the special needs of our customers.

3" x 5" x 12' length Rectangular/Edges Chaffered
3" x 7" x 12' length Rectangular/Edges Chaffered
2" x 4" x 12' length Rectangular/Edges Chaffered

Other shapes fabricated per request.

Continuous Length Fendering System
FITTED PILE WRAPS
Ultra Fend - Ultra High
Molecular Weight Polyethylene Ultra Fend Fitted Pile Wraps are rounded fenders designed to contour individual fronts. Fitted pile wrap panels and beveled along the edges to further reduce possible edge catching and dislocation. Wraps let hulls slide freely along piles and protect wood against chipping and shredding due to impact and abrasion. A 3/4" thick x 11" wide wrap suitable for a 13" diameter pile is drilled with holes 1 1/2" diameter, 1/2" deep countersink, to accept 1/2" diameter bolts with cut washers. Standard fitted pile wraps are available to 12' long.
Fitted Pile Wraps


3/4" x 12" x 12' long
1-1/4" x 12" x 12' long
1-1/2" x 12" x 12' long

VHMW-PE BLACK

Options: Colors/grey
Counter boring for steel pile installation
Stud Welding
Call for pricing on other radius sizes available.
Call for quantity pricing.
PILING CAPS
Neat and easy to install, our piling caps are an excellent and inexpensive way to protect costly pilings from internal rot. Available in 25 sizes, in 1/2" increments from 6" to 18" in diameter. Available in 2 styles, the standard flat or cone-head, is uniquely designed to help discourage sea birds from perching on them. Black caps are made from heavy UV resistant low density polyethylene with estimated life in excess of 15 years. White caps are made of tough, UV resistant TPR synthetic rubber and have an estimated life of 7 years. Call for sizes
Piling Caps
BACK TO TOP
Mooring Systems
Our Mooring Arm systems are GUARANTEED to protect your craft from striking the dock. Independent suspension allows moored craft to freely move up and down (not in and out from dock) so craft can gently ride water action. QUICK and easy to moor up and cast off. EASY to install.

Mooring Arm System: Each system comes complete with 2 Snap Lines, 2 marine-alloy aluminum power-coated universal dock attachments, 2 rigid UV-impervious fiberglass arms, 2 nylon tips, and installation instructions. Arms may be shortened to accommodate any installation.

Lifetime Warranty: Mooring Arms and Snap Lines are warranted to be free from
manufacturing defect for life of the product.

Guarantee: When the proper size Mooring Arm system is correctly installed for the stated craft size, in accordance with supplied instructions and using our Snap Lines performance is guaranteed; moored craft will not strike the dock. Guarantee applies to replacement or refund of the Mooring Arms only.
Mooring System Jet Ski mooring System
PILING MOORING BARS
Dock Hardware & Marine Have developed a rigid mooring bar system for large yachts and house boats so that their mooring loads in severe storms can be applied directly to their mooring pilings, rather than their undersized cleats and docks. This system allows for a straight pull to your mooring in both low and high tide environments. The slider rings are extra strong and will not hang up on the slider bar in stormy conditions. Utilizing this type of mooring system in harsh weather conditions, will assure your valuable investment better chances of survival in hurricane conditions.
Piling Mooring Bars Dock piling Mooring Bars
DOCK SIDE MOORING WHIPS
Designed to prevent damage to boats which are moored in areas which are subject to waves caused by winds and/or boat wake from passing boats. The fiberglass mooring whip acts as a spring to hold your boat off the dock at a safe distance to prevent contact with dock. To board simply pull in on the stern line and the vessel will come along the side of the dock. Lines are made into a permanent assembly and are left on the dock for easy tie up upon return. Bases, tips, and tensioners are cast from aluminum and are coated with bright white polyester powder coating for added protection. Please note some areas are too rough for any type of mooring or tie-up system, do not substitute whips in areas where boat lifts should be used. ~ Build in cleats (2) in each base for spring lines, bow & stern lines ~ Plug in design on 12', 14' & 16' models for easy breakdown and winter storage ~ Braided whip lines & spring lines included ~ Whip rod diameters from 1 3/16"-3/4" ~SS Mounting hardware included ~ Steel reinforced connector ~ 5 Year warranty on whips and bases, on year warranty on lines
Dock side mooring whips Dock side mooring whips
BACK TO TOP
Power Posts
Dock Hardware & Marine, Power Pedestals at a lower cost, suitable for
residential as well as commercial installations. These power posts offer a
choice of either aluminum or steel on or off the dock mounting.
The fiberglass enclosures are watertight, and rated to exceed an outdoor life
of 25 years. Marine grade twist lock corrosion resistant receptacles in
combinations of 30 AMP (110 V), 50 AMP (125-125/250 Volt), and 20 AMP
(110 V) are available. Ground fault GFI 20 AMP outlets also available.
A patented 7 Watt internal fluorescent light controlled by a photo electric
sensor is included. Each unit is designed for 200 AMP 120/240 V AC, single
phase, 4 wire 60 HZ maximum rating. Any combination of receptacles up to 4
is acceptable . Cable TV, brass water manifolds, and digital electronic
kilowatt hour meters are available at an additional cost. Listed below are
some of our most popular models.
Power Posts Power Pedestals
BACK TO TOP
Break Waters
.: Heavy Duty
Heavy Duty Pontoons
BACK TO TOP
.: Breakwater4000
Breakwater 4000
BACK TO TOP
.: Breakwater2700
Marinetek Breakwater 2700
BACK TO TOP
.: 1000-1024-1030-1040
Concrete Pontoon type sf 1000
BACK TO TOP
.: 1530-1540-1550
Data Sheet for type 1530 1540 1550
BACK TO TOP
.: 1800-1840-1850-1860
Concrete Pontoon type sf 1800
BACK TO TOP
.: 300-400-500
Concrete Breakwater type sf 300 400 500
BACK TO TOP
.: 1200-1230-1240-1250
Concrete Pontoon type sf 1200
BACK TO TOP
Dock Hardware
You can construct anyone of our typical floating docks, using the various wood dock hardware components we manufacture. All our wood dock hardware, is made from 1/4" thick high strength steel and coated with plating of hot dipped galvanizing. Using pressure treated building materials, 1 1/2" or 2 1/2" thick, from 6-12" wide, your floating docks can be constructed to withstand any marine environment.

Our wood dock hardware is fastened to your stringers, or substructure using 1/2" galvanized carriage bolts, and the connectors can be connected with 3/4" pins or 3/4" hex head bolts with locking nuts.
Outside Female Corner Outside Male Corners
(OFC) Outside Female Corner - is used to
interconnect with male outside corners, male backer plates, and heavy duty male outside corners. Great for connecting main docks, finger piers and ramps to floats.
Call for prices
(OMC) Outside Male Corners - are used to
interconnect with outside female corners,
female backer plates, and heavy duty female outside corners. Great for connecting main floats, etc. Connecting pin is 3/4" in diameter. Call for prices
Outside Terminal Corner Outside Corner
(OTC) Outside Terminal Corner - is used to
connect stringers to end stringers and is
usually backed up with one of our corners.
This corner piece will keep your main floats or finger piers square.
Call for prices
(IC) Outside Corners - are used to back up all our male, female, and outside terminal
corners. The welded Gusset gives this piece of hardware strength characteristics that adds to your floats longevity.
Call for prices
Outside Female Corner Heavy Duty Outside Male Terminal Corner
(HDOFC) Heavy Outside Female Corner - is
used in areas with extreme wind or current
flows. Heavy duty male outside terminal
corner interconnects with this hardware.
Backed up with an inside corner.
Call for prices
(HDMOTC) Heavy Duty Male Outside
Terminal Corner - is used in areas with
extreme wind and current flows.
Interconnects with heavy duty female outside corner. Back up plate is an inside corner. Call for prices
Outside Female Terminal Corner Outside Male Terminal Corner
(OFCS) Outside Female Terminal Corner
(Special) - is used to connect a finger section to main floats where two main docks sections join together. Backup is an inside corner. Call for prices
(OMTCS) Outside Male Terminal Corner
(Special) - is used for floats that need to be
connected at both ends and at the side of
the float. It is backed up with an inside
corner. Call for prices
Galvanized Leg Angles Hardware Single Female T Connectors
(QCGM) Hardware: These 3" x 3" x 5/16" galvanized leg angles are pre-punched to accept 3/8" gal lag screws or 1/2" galvanized bolts for connection to
flotation modules we sell. Our mounting hardware comes in various lengths and all are pre-punched to offer 4-6 attaching points per leg. Call for prices
(SFTC) Single Female T Connectors - are
used to connect sections to bulkheads, floats to floats, finger piers to floats. Used in
conjunction with male T connectors, and
male outside corners. The female T
connector is backed up with our backer
plates. Call for prices
Single Male T Connectors Stabilizer Plate Angle
(SMTC) Single Male T Connectors - are
used to connect floats to finger piers, and
floats to connecting ramps, etc. The single
male T connector is backed up with our
backer plates. Call for prices
(SPA) Stabilizer Plate Angle - allows for
framing greater surface area and that
architectural look to your finger piers.
Backed up with our backer plates.
Call for prices
Male Finger Deck Stabilizer Plate Backer Plate
MSP) Male Finger Deck Stabilizer Plates -
provides connection and stabilization of
your finger piers, as well as providing
greater surface area and that architectural
look. Backed up with our backer plates.
Call for prices
(BP) Backer Plates - are used to back up all
our single T connectors and stabilizer
plates. 5/8" SQ. Holes.
Call for prices
Half Washer Plate Pipe Stabilizer
(HWP) Half Washer Plate - is used as a
backup for our angle braces and cleat
angles. Fabricated from 3/16" thick steel
with 5/8" SQ. Holes.
Call for prices
(PS) Pipe Stabilizer - is used to stabilize
finger sections from that annoying side to
side and up and down motion. It is used in
conjunction with female T connectors.
Call for prices
Angle Brace Chain Retainer
(AB) Angle Brace - is used to connect cross
stringers to side stringers as opposed to
nailing. One of our half washers plates is
used as a backup.
Call for prices
(CHR) Chain Retainer - is used to secure
your anchoring chains to your float. Ideal
for providing quick slack adjustment to your
anchoring chains. Suitable for 3/8" or 1/4
anchoring chains.
Call for prices
Utility Channel Splicer Plate Set
(UC) Utility Channel - is used to run
electrical conduit through wood dock ends
and cross stringers.
Call for prices
(SP) Splicer Plate Set - Consists of splice
plate and backup plate. Used to connect
side stringers to form desired length of dock
or finger pier.
Call for prices
Straight Dock Brackets Corner Dock Brackets
Straight Dock Brackets
Call for prices
Corner Dock Brackets
Call for prices
Mud Pads Auger Bits
Mud Pads
Call for prices
Augers
Call for prices
Driving Caps Exterior Wood Finishing System
Driving Caps Call for prices ~Same day 100% acrylic exterior wood
finishing system
~Lustrous, premium wood finish
~Apply to new, wet wood
~Clean and coat in the same day
~Available in 8 premixed colors: Natural,
Cedar, Natural Honey, Chestnut, Sedona and
Redwood
Available in 1gal. Or 5gal.
BACK TO TOP

Dock Hardware & Marine Fabrication, LLC
Copyright 2007-2009 . All Rights Reserved
.